AquaCrystal Sand Filter Hex Drain Plug
Replacement lower drain plug for compatible Illuminex AquaCrystal sand filters.
Confirm your AquaCrystal filter model before ordering.

Hex Drain Plug
Replacement drain component for the lower tank drain location on compatible AquaCrystal sand filters.
Temporarily Out of Stock
Contact our team for current availability or help confirming the correct AquaCrystal drain plug.
Lower Tank Drain
Replacement component for the approved AquaCrystal sand-filter drain location.
Service & Winterization
Provides access for approved filter draining during maintenance and seasonal service.
AquaCrystal Fit
Confirm the filter model and replacement-part number before ordering.
Closes the AquaCrystal Tank Drain
The drain plug seals the designated lower drain opening on the compatible AquaCrystal sand-filter tank during normal filter operation.
When draining is required for approved maintenance or winterization, the drain component is serviced according to the current AquaCrystal instructions.
This Drain Plug Is a Drain Component β Not a Pressure or Flow Device
Compatible AquaCrystal Filters
This drain plug is categorized as a replacement part for the AquaCrystal sand-filter family. The models below are the current AquaCrystal configurations β exact replacement compatibility for this specific drain plug must be confirmed before ordering.
Do not assume this drain plug fits every AquaCrystal model solely because they belong to the same filter family. Several AquaCrystal filter illustrations show a lower drain fitting, but that does not prove the same thread, plug diameter, seal, or part number across all models. Confirm the exact replacement-part relationship before ordering.
Where It Fits
Conceptual location of the hex drain plug on a compatible AquaCrystal sand filter.
Conceptual product-location visual β refer to the current AquaCrystal filter manual and parts diagram for exact installation details.
Drain Plug Details
Only confirmed information is shown. Thread size, thread type, plug diameter, and seal design are not published unless verified in the product record.
Hex Design
The hex-shaped exterior is part of the approved part design. Install and remove the drain plug according to the current AquaCrystal service instructions.
Wrench size, socket size, and tightening torque are not published unless approved AquaCrystal service instructions specify them.
Thread specifications (NPT, NPSM, BSP, metric, diameter, pitch) are not published unless confirmed for this exact drain plug. Filter valve size and inlet/outlet size are unrelated to the drain-plug thread.
Built for Filter Draining & Seasonal Service
The lower drain provides access for removing water from the compatible AquaCrystal tank during approved maintenance and winterization procedures.
Removing the drain plug does not automatically remove sand media, internal laterals, standpipe, or the multiport valve. Follow the current AquaCrystal manual for approved draining and winterization procedures.
Depressurize Before Service
Turn off the circulation pump and fully relieve pressure from the filtration system before removing or servicing the drain plug.
Follow the current AquaCrystal manual for approved draining and winterization procedures.
Never loosen the drain plug while the filter is pressurized.
Never remove the drain plug while the pump is operating.
Do not use the drain plug as the primary pressure-relief method.
Do not open the multiport valve or filter tank before pressure is safely relieved.
Service Steps
Stop the System
Turn off the circulation pump before filter service.
Relieve Pressure
Fully depressurize the filter according to the AquaCrystal instructions.
Service the Drain
Remove or reinstall the drain component only after the system is safely depressurized.
When Should the Drain Plug Be Inspected?
Visible Damage
Inspect the plug for visible cracking, deformation or other physical damage.
Seal Condition
Inspect the approved sealing component and mating drain surface during service.
Drain Connection
If the drain area does not seal correctly, inspect the plug and sealing components according to the AquaCrystal service instructions.
Replace When Necessary
Use the correct AquaCrystal replacement part when the existing drain component is damaged or no longer serviceable.
What's Included
Package contents come from the actual product record. No O-ring, gasket, seal, washer, tool, or adapter is shown unless actually included.
O-ring or gasket inclusion is not assumed β if a seal is sold separately, it appears under Related AquaCrystal Replacement Parts.
Confirm the Correct Drain Plug
Find Your Filter Model
Locate the AquaCrystal model number on the filter label.
Identify the Drain
Confirm that the component requiring replacement is the lower sand-filter drain plug.
Match the Part
Confirm the model and approved replacement-part number before ordering.
Contact Us About Availability
Tell us about your AquaCrystal filter and we'll confirm the correct drain plug and availability. Your request automatically references this product.


